-starp 옵션 미적용시 32정도 셋팅으로 돌리고 있었습니다..
( asus 1080 알약 적용 )
nvidia 드라이버 버전올리고
claymore도 12버전 쓰다가 최근에 올리면서
안돌아가서 검색후 테스트 모드 적용하느라 고생하고 검색하여 테스트모드 적용하고 .. -strap 옵션이 안먹어서 좌절하다가...
( windows 10 테스트모드 설정
bios secureboot disable 상태에서
관리자권한으로 명령창을 열고
bcdedit -set loadoptions DISABLE_INTEGRITY_CHECKS
bcdedit -set TESTSIGNING ON
입력후 재부팅하면 됩니다. )
-strap 옵션 1 2 3 4
넣어주면 다 죽어버리더군요...
그래서 claymore 설명서를 보던중
-strap applies specified memory timings (strap). This option is available for Windows only and requires AMD blockchain drivers or drivers 18.x or newer (most tests were performed on 19.4.3) for AMD cards, any recent Nvidia drivers for Nvidia cards.
Currently Polaris, Vega and Nvidia 10xx cards are supported, support for other cards will be added later.
Miner has built-in straps database, all straps are separated by memory (4GB or 8GB) and memory type (Samsung, Elpida, Hynix, Micron).
Straps are sorted by intensity, i.e. "-strap 1" supports higher memory clock than "-strap 2", etc. For the best hashrate you must also set high memory clock, so "-strap 1" is a good start point for tests.
You can specify just strap index, for example "-strap 1" will apply first strap from database for all Polaris GPUs based on GPU memory size and memory type, miner will show full strap name detected.
Or you can specify strap directly in format "POL8S1": "POL" means Polaris, "8" means 8GB, "S" means Samsung memory, "1" means index.
Zero index means default strap from VBIOS, i.e. no strap is applied.
You can also use "@" character after strap to specify memory clock, it works like "-mclock" but overrides it, for example, "-strap [email protected]". For Nvidia you can also specify delta, for example, "-strap [email protected]+700".
You can also specify values for every card, for example "-strap [email protected],POL4H3,0".
If strap is applied, miner will return old strap and memory clock when miner is closed.
The best approach to find best strap is to set "-strap 1,0" (it sets strap #1 for first card and no straps for the rest of GPUs) and then raise memory clock to see what clocks and hashrate you can reach.
Then so the same for strap #2 etc.
You can also specify raw strap string (96 characters). Note that single option value means that this strap is applied for all GPUs, use "0" to apply strap on single GPU,
for example "-strap 0,[email protected],0" applies strap #1 and memory clock 2200MHz for second GPU only.
NOTE: if specified strap fails, Windows is crashed. After reboot default timings are restored and you can try some different settings.
NOTE: Polaris cards have different number of straps (depends on memory type and size).
Vega cards have "-strap 1" ... "-strap 5" values.
Nvidia cards have "-strap 1" ... "-strap 6" values (1...3 are normal straps and 4...6 are low-intensity straps).
-sintensity strap intensity for Nvidia cards, in %. Use this option to adjust strap intensity for Nvidia cards if even straps with lowest intensity ("-strap 1" and "-strap 4") are unstable on your cards.
To find best value, use "-strap 4 -sintensity 1" and see if it is stable. Then increase "-sintensity" value (maximum value is 100) to find best stable hashrate. Then try other "-strap" values.
You can also specify values for every card, for example "-sintensity 10,0,100,30".
Default value is "0" which means no changes in default strap settings.
nvidia card는 -sintensity 옵션을 추가로 적용해야된다고 되있더군요..
그래서 -strap 1 -sintensity 1 -> 재부팅
-strap 4 -sintensity 1 잘돌아가지만 해쉬 증가 없음
-strap 4 -sintensity 10 해쉬 2증가...
음... 더 올려볼까 하다가 다시 자러가기전에 기쁜소식을 올려봅니다.. ^^